Ormarica iskra avtomatika ljubljana e 10 tig

[slaviša]

rabim sliko ali načrt visokonapetosnega transformatorja z deli ki se nahaja v ormarici levo piše visoka napetost ker sem po okvari pred letom vrgel stran tako da sedaj ko sem nabavil drug trafo ne vem kako je vezan in kateri deli še pašejo noter je pa pobebej zaprto v ohišju ki se enostavno odvije.

[PartyBoy]

dobiš

[PartyBoy]

Tukaj imaš slike, upam da ti bodo pomagale

[PartyBoy]

Aja pa še tole bi uprašal:
KAM GRE TALE ŽICA, KAM SE PRIKLOPI ???


ALI MORA BITI TU KAJ PRIKLOPLJENO ???

[kopron]

Ta žica je drugi izvod od visokofrekvenčnega vžiga in gre na varjenec ali pa na plus pol na usmerniku.Drugi konec pa je priklopljen na pištolo.Pazi pri varjenju z TIG-om je vedno na pištoli - pol, + pa gre kot masa na varjenec.

[PartyBoy]

To se pravi, da je žica (k so trije ~) kot masa ??? ali moraš imeti 2 masi ??? Pa maso na usmerniku moram potem priklopit tam ko je na usmerniku pištola (+)

[kefaja]

please can you upload images again
thanks in advance

[magnum44]

Tukaj imaš slike, upam da ti bodo pomagale

zakaj jaz ne vidim slikic ?
se mi zdi že malo butalsko.
Ali so narisane z nevidnim črnilom?
Rabim kak posebni daljnogled, za ogled?
Ali bom moral iskati tri dni navodila, ker je nek poseben način da lahko vidiš tisto, kar nekdo prilepi?

[Slavc]

Tukaj imaš slike, upam da ti bodo pomagale

zakaj jaz ne vidim slikic ?
se mi zdi že malo butalsko.
Ali so narisane z nevidnim črnilom?
Rabim kak posebni daljnogled, za ogled?
Ali bom moral iskati tri dni navodila, ker je nek poseben način da lahko vidiš tisto, kar nekdo prilepi?

Če pogledaš pod lastnosti je očitno, da slike na strani "shrani.si " ni več na voljo. Očitno je bila dana le povezava na stran .

[kefaja]

Yes that's right the images was uploaded long ago
but please does anyone have these images or this unit
thanks

[kefaja]

this unit Iskra e-10m ac/dc tig control unit comes with Koncar CT-300ac/dc mma welder
I cant start ac tig welding whit this
do I need something else to do it some device which I dont have like capacitor battery ,choke or something else
or this unit Iskra e-10m not function properly
thanks

[kenny]

You only need to switch hf start only for dc and continuous hf for ac. If you're not getting any hf, then it's a problem with e10. Dc works normaly ?

[kefaja]

yes dc tig works normally
are these two complete unit I dont need something else
here is the schematics off hf unit , maybe orginal
there is no name or code on my hf unit

[kenny]

You can try swaping contactors in e10. It's probably either bad contactor or something else on the card.

[kefaja]

I dont have schematics of Iskra e-10m
all relays are ok and pcb is ok and components on it are all ok
there are two connectors on one side of this unit for command ,I will post picture later,one for connection between unit and welder and one for external command ,I think,
and one for torch from other side
but someone cut it out these connectors
I tried to reconnect everything back but withtout schematics
I hope that someone have these schematics or pictures of unit